Category: Kitchen Cabinet

Get a Handle on Installing Cabinet Hardware

Now that youve picked out the hardware of your dreams, you need only to install them to finish the look of your cabinets. If youve never installed hardware before, you might be intimidated by the idea of using a level or marking off the correct spots for placement; you might be particularly intimidated by the thought of using the dreaded drill. Take a breath before you begin and dont worry about the task ahead. The entire process is easy and fairly quick. Make sure to have the following tools on hand as you start. This will ensure a smooth process and will diminish the chance of a mishap.
1.Drill (most commonly a 3/16 drill bit)
2.Level
3.Marker
4.Masking tape
5.Nail or center punch (to make an indentation for where to start the drilling)
6.Screwdriver (Phillips or flathead depending on your specific hardware)

Knobs or handles

Whether you are installing knobs or handles, you should first try to choose a piece that has the same drill center(s) as the existing hardware. If you are choosing hardware for cabinets that havent been drilled before, knobs are the easiest choice since they have only one screw. Some types of knobs and handles come with attached screws, making a simple procedure even more effortless.

If youve chosen to install pulls or handles, youll need to measure the distance between the drill centers. Do not measure the length of the handle, as the handle itself may extend beyond the drill centers.

Let the installation begin

Solid wooden cabinets and drawers might split as a result of drilling into them. In order to avoid this, refrain from drilling holes closer than an inch from the edge. Standard contemporary flat-panel doors are complemented nicely by knobs installed 1 to 2 from the open corner of the door. Pulls should be installed 2 4 from the bottom horizontal edge of the door and 2 from the open vertical edge. After youve marked off the correct places for drilling, simply drill holes and insert the hardware screws into the holes. Match up the screws and the handle or knob and, using your screwdriver, tighten until the hardware doesnt wobble.

In general, cabinet doors are made of the lumber; in this situation, the standard 1 screw will fit perfectly. Drawers with applied faces, for example, might be thicker than usual and will likely require longer screws. When purchasing hardware, be sure to specify to the vendor your special requirements.

Now, with all of this new information, you are ready to get busy! Install your new hardware and give your cabinets a face lift. Who knew that such a straightforward process could yield such beautiful results?

More Storage with Kitchen Cabinets

When it comes to kitchens, one of the most important elements to maintain beauty and functionality is storage. To keep things as organized as possible leaving the heart of your home clutter-free and pleasing to the eye, enough space to stash away all your cooking and dining items should be ensured. With this said, this article discusses how to achieve more storage with kitchen cabinets.

Cabinet Organizers

Adding more storage does not necessarily mean more or bulkier kitchen cabinets. Making use of what you already have is the smartest way to efficiently add space. Try to open your cabinet doors and look at your cupboards and shelves to see how things are arranged. Here are some tips on how you can organize the contents better:

1.Take out items that are in bulky packaging and keep them in stackable containers instead.
2.When shopping for containers opt for clear ones so that you can easily distinguish what is inside without having to take out contents of the cabinet.
3.Get rid or rounded containers and replace them with rectangular or square ones.
4.Avoid frustration when looking for items by placing often used things in easy to access cabinets and group things together such as one place for all utensils, another entirely for food, etc.
5.Consider buying and integrating innovative cabinet organizers into drawers and kitchen cabinets. Such products include: Utensil Drawer Organizer, Utility Cookware Divider, , Knife Block Drawer Organizer, Base Filler Pull-Out, and Single or Double Base Waste Basket Pull-Out

Window Seats

Accentuate your windows while adding more storage with low base kitchen cabinets as window seats. Other than extending the space where you can keep your items, you will also be adding to the stylishness of the area. Just make sure to create oneness in the design by implementing the same finish or repainting your windows to complement with the new window seat cabinets and build units with the exact sill height and width of the window.

Beyond Standards

When adding kitchen cabinets to achieve more storage, skip the standard sized wall and base cabinets (not unless you have all the floor area that you need). There are types and constructions that allow homeowners to enjoy more storage without taking up too much space.
Sideboards are perfect for keeping small items such as utensils or linens and can be placed anywhere since these units are free-standing.
For your appliance cabinet needs, choose from different sized oven cabinets.
Tall pantries are ideal for general storage that takes up minimal floor area due to their height.
Free standing kitchen islands can be used in many different ways aside from holding cookware and other items. These can also be used as a breakfast table, or an extension to your counters.
Lazy Susan cabinet helps maximize use of space by allowing easier and more convenient access.
Drawer base kitchen cabinets are specially designed to better organize smaller items such as cutting tools, utensils, and cooking spatulas.

Ten Quartz Countertop Benefits

The list of benefits from using a natural stone like quartz over manufactured countertops like formica and corian is outstanding. Quartz counters will even service your kitchen needs better than granite counters.

Quartz surfaces combine the best qualities of laminate counters and natural stone surfaces into one cutting edge product. Quartz surfaces began appearing on home remodeling jobs in just the last few years but its popularity is boiling over. The market share of natural and engineered quartz has risen so quickly that granite quarries are petrified. Granite has been the interior designers and architects countertop of choice for decades.

A small minority of quartz countertops are made of natural quartz cut from monolithic blocks of stone harvested from quarries. The majority of quartz countertop sold today are manufactured from about 95% crushed quartz and 5% polymers. The infused materials result in countertops that are nearly scratch proof, almost maintenance free, and the process allows the counters to be available in designer colors that range from translucent whites to sandy browns or monolithic blacks.

The color choices are what excite most homeowners. With the open floor plans of many kitchens spreading out into dining and living areas it is important for designers to coordinate countertop color choices with the rest of the house. Renovating kitchens with natural flow into the rest of the home becomes a piece of cake.

Easy list of quartz countertops designer benefits:

Quartz is the most durable countertop stone or manufactured countertop you can buy

You can install quartz tiles or monolithic slabs on shower walls

Designer color choices are available

Custom edges can be created

Quartz countertops dont need to be sealed like granite surfaces

Ability to install an undermount sink

Faucets can be installed directly on the counter

Hot pots and pans can be placed on the working surface of the counter

Quartz countertops pay for themselves by adding value to your home

Bacteria have a harder time taking hold in quartz counters than any other countertop

The best features of quartz countertops are not visible from the surface. The inside of the counter is where the most benefits crystallize.Quartz countertops are the nearly indestructible counters you can install. Most manufacturers offer a warranty if your counter is installed by a licensed home improvement contractor. Try getting that with a granite countertop.

Final Tip: Don’t pelt quartz counters with large diamonds as the countertop might chip. Diamonds are one of the few natural minerals that are harder than quartz.

Kitchen Cabinet Installation – Do it Yourself

You have a kitchen remodeling project and you want to tackle the kitchen cabinet installation yourself, but you are not quite sure where to start. I will be glad to lend you some of the basic information on how to install kitchen cabinets so that you will feel more confident with your remodeling project.

I cannot stress enough the importance of getting familiar with your new kitchen layout. Go over the drawings and visualize how the finished kitchen will look. This will help you feel more comfortable when you start with the installation. Also, make sure that each and every cabinet that you hang is level and plumb. This is very critical. Take your time and get it right.

There is more to installing kitchen cabinets than most people realize. There is more to it than just drawing out lines on the wall and fastening the cabinets. Sure, you can just throw the cabinets against the wall and screw them in place, but the end result is going to look like it as well. I have had many carpenters tell me that what I did for a living was “cream work” until they actually tried to install some of the kitchens that I have installed over the years. When it came to actually installing the kitchen and installing it the right way, they were totally lost. They found out in a hurry that when it came to just installing kitchen cabinets as opposed to knowing how to install kitchen cabinets that were two totally different things altogether.

Now I am not saying that you need to be a seasoned professional to install kitchen cabinets, but you do need to understand at least the basics of kitchen cabinet installation if you want to tackle your own kitchen remodeling project. Making sure that the cabinets are level, plumb, and in a straight line with each other is the most important aspect to any kitchen cabinet installation.

Let us say that you have chosen a granite counter-top and have all of the base cabinets installed and the fabricator shows up ready to template for your counter-top, only to find that the base cabinets are out of level ever so slightly or they are not in a straight line or they have some minor dips or humps between them. The fabricator more than likely is going to pack up his equipment and advise you that the cabinets will have to be adjusted before he can come back to make the template. A stone counter-top fabricator will not install their product unless the cabinets are perfectly flat and level. Stone is totally unforgiving, and if there is a slight hump in the middle of the run of base cabinets, it is going to cause a huge problem for the counter installation.

Your kitchen cabinet installation needs to be precise in order for everything else to fall into place. You can install kitchen cabinets yourself and save money in the process, but if you are not careful, then the mistakes that you could possibly make will eat into those savings.

Federal Brace, A company on the move.

This week Ive chosen to recount the incredible year Federal Brace has had bringing their customers Beautifully Crafted, Confident Supports. They have doubled their countertop bracket line by announcing the release of ten new styles. These fresh new countertop bracket designs augment the large selection of countertop supports already available under the Federal Brace brand.

The companys new Enterprise Support, Foremont Support, and Perrine Decorative Support styles are part of the new countertop mounted support line. The use of these brackets within this application type is to support an elevated bar directly from the lower countertop level. The brackets are mounted directly to the sub-counter and elevated on a counter or a bar on support plates at the top of the bracket.

Federal Brace announced the Bracket Backer , a designing enhancement with backer board trim that protects soft wall material behind brackets in heavy weight applications. This product is designed to prevent sheetrock flexing or crushing of soft wallboard materials.

They provide free video guides and tips regarding countertop and countertop bracket installations. These videos feature trained professionals using various support styles and types in many different applications. They create these videos for the benefit of their customers so they may gain knowledge of the countertop installation process and to see their countertop supports in action.

Federal Brace is no longer just a kitchen countertop support company. To finish out a year of expansive growth, the company is introducing a full line of sixteen shelf brackets. These new offering will include designs from Federal Braces most popular countertop support models. Now customers can match their countertop supports with decorative shelf brackets elsewhere in the home.

The Brunswick style support was featured for The KBISs Best In Show, in Chicago, where it garnered much interest and positive comments related to both its strength and style. At the IWF show, in Atlanta, wood workers marveled at the craftsmanship of the brackets and showered Federal Brace with positive comments.

When it comes to the customers needs, their needs are their number one focus and the driving force of their business. To meet the needs of the consumers they have expanded their offices and added more personal. They have added more dealers and distributors throughout the continental United States. Federal Brace has helped thousands of homeowners with countertop support solutions and is steadfast in supplying Beautifully Crafted, Confident Supports for America. Onto 2011!

When all is at hand in the kitchen.Part2.

Sliding sections of cupboards are good for large and small kitchen. Because they are not wide their depths is used reasonably. Food is kept in the latticed boxes. Such section rolls out easily, food is well visible and can freely be taken out from any side. It is easy to roll the section back; last inches are pulled inward automatically. For those, who prefer their cupboards to cover the whole wall, we recommend multi-tier cupboards. It will allow rolling out only the necessary part. If you set an oven ergonomically, there will be no need to bend over. It would seem that nothing will be placed in a few inches. If you equip it with moving cupboard, it will be possible to place a lot of various small things.

There is a great range of hidden storage systems, which allow using difficultly accessible corners, niches, empty spaces effectively. For example, there is such an innovation, as three-level micro lift which lowers a shelf with all of its content.

There are a lot of roomy sliding baskets of different sizes. It is convenient to keep all the detergents under the sink in a sliding basket. Various open units, such as shelves, niches, wall panels, decorative columns with boxes give additional possibilities for space constructing and designing.

Such accessories as hooks for ladle, a stand for bottles and glasses, plates drier, appliances for paper towels, a trivet for hot things and others offered by modern companies also allow designing nice functional kitchens. As a rule, things contacting water or storage of detergents, a corner column or space under the sink is covered with stainless steel.

A drop-leaf serving table on wheels with sliding cutting board is very comfortable. The lower open shelf for plates is supplied with stoppers; the piles of sparkling clean plates become the element of interior. Such new decisions of space designing and logical combinations are developed as exclusive elements of kitchen furniture of high class. But unfortunately we change kitchens rarely. And what can be done, if your kitchen does not satisfy you with such innovations?

It is possible to fit wall cupboards with sliding doors in free niches, even when opened they do not take a lot of space, which is so necessary in a little room. Similar constructions extend space ideally. The revolving vertical bar will take minimum space and is very comfortable at the same time. Use the space between a working surface and wall cupboards to fit a narrow shelf or railing system on the wall between them. It is possible to keep kitchen utensils which usually take space on a working surface on them. Consoles for holding a microwave on a wall free the working space on a working surface. Microwave can be placed in a cupboard.

It is convenient to hang on railings not only kitchen utensils but also small decorative things. Additional possibilities of sliding tables can be used not only for the evening tea-drinking but also for preparation of food on them. Movable or folding dinner-table mounted in a wall behind a door may be of service. Even a kitchen board can be compacted between table top and a sliding drawer. A bin is not that important, but if you place it right, it will save you from many additional movements. Kitchen comfort is the absence of problems with finding small things, the possibility to find a maximally comfortable place for everything. It is when everything works comfortably, quietly and easily. When, professionally speaking, kitchen space is rationalized.

Ideas and Options for Kitchen Cabinets

When it comes to remodeling the heart of your homes, one of the major things to consider is the kitchen cabinets for being among the most visible and functionally important features of the area. For these same reasons, cabinetry is where a large portion of the entire remodeling project goes. Thus choosing kitchen cabinets to get you the best value for your money is crucial. This article lays out ideas and options to help you in your home improvement quest.

Kitchen cabinets can be bought online or offline. There are advantages and disadvantages for either choice but it all boils down to your personal preference. One good thing about shopping today though, is that most storeslocal or widely branched have already tapped into this great and cheap advertising medium which is the Internet. Now, you can choose from any stores collection online to save up on gas and enabling yourself to see more without all the legwork. But if you want to see the items for yourself, and really get an idea on how the cabinet pieces look and feel then going to showrooms would work best.

Traditionally, kitchen cabinets come as stock, semi-stock or custom-made. What sets one type from the other are costs and assortment from which you can choose from. Stock cabinet pieces though the most affordable, come in a limited array of popular designs and finishes. On the contrary, custom-made cabinetry gives you the freedom to get the exact same features as you want them but can be very expensive. And semi-stock kitchen cabinets come in the middle in terms of price and assortment.

Today, one of the most popular products in the home improvement industry is the RTA kitchen cabinets. Ready-to-assemble, they come packaged with everything needed to put the pieces together successfully without any special tools or skills. Flat-packed, these are easier to store as well as faster to transport. RTA cabinet units come in the cheapest particleboard and laminate to the most luxurious hardwood species. This choice makes up for a cheaper as well as faster alternative.

But before buying, there are factors that you have to consider so as not to end up wasting time and money.

Budget Making up for around 40 to 50% of the overall remodeling budget, it is important to know how much you can afford and are willing to spend.

Layout one of the deciding factors when choosing whether to go for traditional stock, semi-stock, custom-made; or RTA kitchen cabinets is the layout of your kitchen. If yours is not the typical square or rectangular room but has differently shaped corners, then custom-made might prove to be the most space-efficient choice.

Dimensions Having accurate measurements of the available space that you have for your kitchen cabinets helps prevent mistakes of picking a set that is too small that results to imbalance in the design or one that does not fit at all.

By doing your part and researching on ideas and knowing your options, you are affording your home the quality and best fitting style that your money can afford. Choose and buy kitchen cabinets wisely.

Kitchen Design Ideas

Kitchens have evolved a lot over the years. Once found only in the rear of the house, today’s kitchen design takes the kitchen out the background. The challenge for kitchen design is in creating a more open-faced kitchen, that is part of a dining area, a family room or a great room.

In deciding on how to design your kitchen, you must take into consideration such things as: will your kitchen have an island? Will it be of a modern or traditional design? What kinds of appliances will you need for your new kitchen design? What kind of lighting design?

1. Kitchen as ‘Great Room’ Whether you are redesigning an existing kitchen or planning a new kitchen in a new home there are some design considerations to keep in mind, such as including in an island or peninsula as part of the kitchen design. These can be used to connect the kitchen to a nearby dining area or family room thereby creating a ‘great room’. A kitchen island or peninsula will allow the cook to keep in visual and conversational contact with family members or guests in the adjoining family or dining room.

2. Create a Kitchen Canopy To give the kitchen some visible borders without blocking views create a kitchen canopy. Also a high ceiling in the kitchen can create the perception of spaciousness.

3. Using Kitchen Cabinet Color to Set Tone of Kitchen Design Kitchen cabinets will help set the tone for the whole room. The choice of wood will influence the overall look of your cabinets. To create a light look, use a light wood such as ash, beech, birch, oak, maple, or chestnut. For medium range, select cherry. To darker kitchens, choose wood that has some color to it.

4. Plan Out Use of Cabinets and Drawers in The New Kitchen Design Plan out in the kitchen design blueprint just how your cabinets and drawers will be used and how much space and storage you will need before you start your new kitchen design. The first thing to examine is the counter surface area. Look at where you put everything in your existing kitchen and where in your new kitchen design will these things will go in the new space. Will there be more than one person cooking at a time. If so, will there be enough room for two cooks in the kitchen to work together?

5. Use The Galley-Type Kitchen Design As for counter arrangements, many kitchen designers agree the galley-type design to be the best in terms of efficiency with it’s single aisle and counters to either side, making it easy to turn around to go from sink to cooking range.

6. Under-Cabinet Kitchen Lighting Kitchen lighting can be an overlooked area of kitchen design. Even if the kitchen has generally good lighting, the counter areas can be somewhat dark. For these areas under-cabinet lighting can help provide more light to work in. By using simple spots or fluorescent lights a smaller kitchen can be made to look larger.

7. Looking at Countertops Granite, marble, and limestone are all popular natural materials for use in countertops are available in many colors. Ceramic tile kitchen countertops are versatile, practical, and also available in many colors, as well as many shapes, patterns, and finishes. Solid surface countertops provide seamless acrylic faces. Solid surfaces also come in almost limitless colors, patterns, and styles, and are stain and heat resistant. Laminate countertops are more affordable but not built to last. Concrete countertops are known for versatility, as well as strength. Wood countertops are long lasting and easy to clean and repair but the wood will not withstand exposure to water and household chemicals. Stainless steel countertops lack the elegance of granite or tile. These countertops do not absorb stains, but tends to scratch easily.

The Basics of Drywall

In the recent past, many American homes contained walls that were made of gypsum plaster – a combination of powder and water applied over a wire mesh. This process was rather lengthy and in an effort to meet the demands of a growing population and need for faster building, drywall was invented.

Also known as plasterboard, drywall is made of pre-dried plaster panels: plaster or wood pulp or other materials. Used primarily to form the interior walls of houses, your contractor may erect drywall as part of building a home addition, garage, or even as part of refinishing your basement.

While you’re patiently waiting for your contractor to build your private masterpiece, you’ll appreciate how well things start to come together and look almost complete once drywall is erected.

Drywall Is Fast!

Drywall comes as sheets of plasterboard of various sizes. Depending upon the use of a room, your contractor may choose thicker plasterboard especially in a room for young children and bouncing toys. Thinner plasterboard is appropriate for areas of the house used less frequently. Using these panels, your contractor will essentially line them up against the studs of the wall’s structure and hammer the sides of them into the wood. The process is repeated when applying drywall to the ceiling as well.

Although measurements and secure nailing is important, the artistry of drywall begins during the taping stage. Taping is the process of concealing the joints between drywall panels. It isn’t hard to imagine that placing drywall panels next to each other creates unsightly lines or gaps. These gaps are called joints and taping conceals them. But this isn’t ordinary tape that we’re talking about.

Signs Of A Good Drywall Job

Contractors tape drywall by first covering its joints with cement, then with a paper strip, and then with more cement. After using a few smoothing techniques, it’s hard to distinguish where a drywall panel starts and ends. In a good drywall job, it’s also almost impossible to find where the panels were nailed into the studs behind them.

And a good dry Waller knows how to patch holes as well. In the past, we were told that repairing a hole by stuffing it with newspaper and patching it with material like Spackle is just fine. Professional contractors will tell you however, that although this method works, it leaves weak spots and there’s a better method that requires the expertise of a professional dry Waller.

Two Signs of A Good Drywall Contractor

Good drywall contractors follow up their initial nailing with a set of second long nails or screws. The second set of nails acts as reinforcement – ensuring that your walls won’t fall down during an important family event or while sleeping! They’re also careful to mix up a batch of cement that doesn’t form air bubbles in the wall’s seams upon drying.

These are just a couple of strategies that your drywall contractor will use to create a surrounding just as secure as the foundation that it sits on.

Cabinet Repairs

Over time, cabinets can go through regular wear and tear just like any part of your home. With that said, it is important to have both preventative and regular care and repair for cabinets in your household. Whether you have wooden kitchen cabinets, or an antique bedroom armoire, it is important to maintain the longevity of your cabinets and storage areas. Maintenance and repairs are crucial to the well being of your cabinets. Refurbishing the appearance is also key.

There are many different ways to restore and repair minor cabinet issues, some of which are very do-it-yourself. One of these includes cabinet re-facing, which is the process of replacing cabinet knobs, doors, and occasionally drawers. A new veneer can replace all of the visible parts easily. Re-facing cabinets is very economical, even for smaller budgets, saving about half the money you would spend on getting new cabinets. It is also a great way to prevent waste in a time when resources are scarce, as keeping cabinets that are in otherwise good condition can be beneficial. Small modifications for re-facing allow you to conserve resources. Also, since most cabinets contain formaldehyde, by keeping old cabinets, you are able to keep this chemical out of the landfill, thus helping the environment. Re-facing is great because there are a variety of finishes on the market to completely revamp the look of older cabinets. New molding and trim, as well as glass can be added for a completely new look. Cabinet re-facing is a great way to spend minimal money to attain a new look from an old set of cabinets.

A common sign of wear and tear in cabinets are problems with cabinet door edges. Sometimes the lines of the doors need to be evened out for both function and appearance. In order to do this, cabinet hinges can be removed easily with a screwdriver. After the cabinet is placed on a smooth surface to work on, a ruler or string can be used to measure a straight edge. Then, a sander can be used to sand off the excess unevenness of the cabinet edge. If the edge is missing, replacement wood can be glued on and sanded down to create the appearance of even doors. Putty can then be used to fill in any of the gaps or seams. Finally, the finished product can be varnished or repainted to look brand new.

Another way to repair or refurbish old cabinets that have poor appearance is to use adhesive painted paper for cabinet doors. This paper, much like sticky wallpaper, is simple, inexpensive, and can truly change the entire look of cabinets. It comes in a variety of colors, prints, and styles that can truly enhance any room. Once the adhesive paper is picked out, it is important to precisely measure the cabinet door to ensure that the paper will fit the exact dimensions and look clean. After the cabinet is cleaned with mild soap and water, it can be smoothly sanded down. Apply the adhesive paper slowly, to ensure that there are no air bubbles. This is a great way to enhance any old cabinet’s appearance quickly and easily.